ASS巨大女人PCiS

        1. ROUNDO HYDRAULIC ANGLE BENDING ROLL, MODEL R6, 6" X 6" X 5/8", 1993, TOOLING

          Brand
          ROUNDO

          Model
          R-6-S

          Stock #
          10460

          Condition
          Not specified

          Year

          Specifications

          Equipped With

          ROUNDO ROLLS R-6-S ( TOOLS 16 )

          MODEL: R-6-S

          CAPACITIES: 

          ANGLES: LEG OUT MAXIMUM 6 X 6 X 5/8 ( MINIMUM DIA. 100" )

          MINIMUM 1-1/2 X 1-1/2 X 1/4 ( MINIMUM DIA. 26" )

          ( WITH SPECIAL TOOLING MINIMUM DIA 16: )

          LEG IN MAXIMUM 5 X 5 X 3/4 ( MINIMUM DIA. 85" )

          MINIMUM 1-1/2 X 1-1/2 X 1/4 ( MINIMUM DIA. 85" )

          ( WITH SPECIAL TOOLING MINIMUM DIA. 18" )

          MINIMUM BEND RATIOS for Diameters:

           LEG OUT= 14X (LEG WIDTH PARRALELL WITH PLANE OF BEND)

          LEG IN= 18X(LEG WIDTH PARRALELL WITH PLANE OF BEND)

          SS 2 x 2 x 3/16, LEG-IN, MIN O.D. = 60”

           

          TEES: LEG OUT MAXIMUM ST6WF36 ( MINIMUM DIA 85" )

          ( MINIMUM DIA 20" )

          LEG IN MAXIMUM ST5WF36 ( MINIMUM DIA. 60" )

          ( MINIMUM DIA. 20" )

           

          FLAT BAR: HARDWAY MAXIMUM 1-1/4 X 5 ( MINIMUM DIA. 48" )

          MINIMUM 1-1/4" X 1--1/2" ( MINIMUM DIA. 20" )

           ( WITH SPECIAL TOOLING 16" )

          Note: 6”wide rolled the Hardway is possible at Larger Radius(240” or bigger)

          EASYWAY MAXIMUM 1-1/4" X 10" ( MINIMUM DIA. 50" )

          ( MINIMUM DIA. 20" )

          SQUARE BAR: MAXIMUM 3" X 3" ( MINIMUM DIA. 50" )

          ( MINIMUM DIA. 20" )

          ROUND BAR: MAXIMUM 3-1/2" DIA. ( MINIMUM DIA. 75" )

          SEE PIPE/TUBE DIE LIST FOR DIA. CAPABILITY.

          ( MINIMUM DIA. 20" )

           

          PIPE: MAXIMUM 5-1/2" STD. PIPE/ 6”OD ( MINIMUM DIA. 75" )

          ( MINIMUM DIA. 20" )

          WF / IBM: HARDWAY MAXIMUM SMALL PROFILES ( MIN. DIA TEST REQUIRED )

          (WF 4” x 13# can be rolled to a 96” inside radius before flange distortion of ¼”)

          EASYWAY MAXIMUM WITH TOOLING 12” X 6-3/8” (WF 12 X 22#)

          ( MINIMUM DIA. 75" ) MINIMUM WITH SPEC. TOOLING

          3” X 2” X 3/8” ( MINIMUM DIA. 20" )

           

          CHANNEL: LEG OUT MAX. SMALL PROFILES (TEST BEND REQ'D.)

          WITH SPEC. TOOLING 12 X 3 ( MINIMUM DIA. 50" )

          LEG IN MAX. SMALL PROFILES (TEST BEND REQ'D.)

          WITH SPEC. TOOLING 3 X 1-1/2 ( MIN. DIA. 20")

          HARDWAY MAX. WITH SPECIAL TOOLING 5 X 2-1/2

          ( MIN. DIA. 160" ) ( MIN DIA. 60" )

           STD PIPE: 1" (1-5/16 OD) MINIMUM CENT. LINE DIAMETER: 16-1/2"

           1-1/2" (1-7/8 OD) " " " " : 18"

           2" (2-3/8 OD) " " " " : 18”

           2-1/2”(2-7/8 OD) “ “ “ “ : 20”

           3" (3-1/2 OD) " " " " : 21-1/2"

           4" (4-1/2 OD) " " " " : 28”

           

           TUBE: 2"OD " " " " :16-1/2”

          Schd 80 Pipe: 3" (3.5 OD) MINIMUM CENT. LINE DIAMETER: 19.25"

          SQUARE/RECT TUBE:

           MAXIMUM HORIZONTAL DIMENSION (HARDWAY): 6”

          MAXIMUM VERTICAL DIMENSION (EASY WAY): 12”

          **1 NOTE THE THICKER THE WALL THE LESS CROSS SECTIONAL DISTORTION WILL

           OCCUR IN ROLLING SQUARE OR RECTANGULAR TUBE. WHENEVER POSSIBLE

           FURNISH A SAMPLE OF THE ROLLED PC IF THE DEGREE OF DISTORTION IS IN

           IN QUESTION OR A CONCERN BEFORE ROLLING THE PRODUCTION PART. AS

           A GENERAL RULE THE RATIO FOR ROLLING IS (WIDTH OF SECTION MULTIPLIED

           BY 18 TO 20 TIMES= MINIMUM RADIUS for Steel, for Aluminum it is 38 to 45 times =MINIMUM

           RADIUS. )

           RT4 x 2 x .125 6061 T6 min Radius inside is 180”(25518-001)

           THE MINIMUM DIAMETER FOR STL ANGLE 2-1/2 X 2-1/2 X 1/4 ROLLED LEG IN

           IS 42” OD (WIDTH OF MATERIAL MULTIPLIED BY 8= MINIMUM RADIUS).

           RT 8 X 3X 1/4 WALL MINIMUM INSIDE RADIUS IS MORE THAN 69” INSIDE EASY WAY

           23X WIDTH OF MATERIAL BEING BENT

          ASS巨大女人PCiS